Each 3535 taper lock bushing product page has the instructions on how to install and remove the bushing, along with dimensions, and wrench torque information to make sure you have all the information necessary to properly install or remove a bushing. Additionally we offer stainless steel and special bore sized bushings per request!

Screw size (BSW): 1/2 inch, hex, socket size: 10mm. Large end dia: 127mm. Bush length: 89mm. Mass: 5.0kg. To Install: 1. Clean shaft, bore and outside of bush, and bore of hub. Remove any oil, laquer or dirt, Place bush in hub and match half holes to make complete holes (each complete hole will be threaded on one side only). 2.

Product overview. Fenner Taper Lock® bushes are machined in cast iron and steel and are available in a full range of both metric and Imperial bores and keyways. They have the equivalent to a shrink-on fit on uniform load applications and offer complete ease of installation and removal. The special 4-hole feature on Fenner Taper Lock® bushes

3535 B 127,0 88,9 4030 B 146,0 76,2 4040 B 146,0 101,6 4535 B 162,0 88,9 4545 B 162,0 114,3 5040 B 177,5 101,6 5050 B 177,5 127,0 Taper Bush Dimensions. Bore (F8) b h mm 1008 1108 1210 1215 1310 1610 1615 2517 2525 3020 3030 3525 3535 4030 4040 4535 4545 5040 5050 9 3 1,4

3535 thru 5050 sizes Dimensions for 1008 thru 3030 BTL Taper Bushings Dimensions for 1008 thru 5050 BTL Taper Bushings W D Ref:Bore+D Position of screw to tighten bushing For removing from shaft Bushing half of hole threaded Hub half of hole not theaded

Taper Lock Bushes are standard conical bushes used as a locking mechanism for fixing pulleys, wheels, shaft couplings and other components to drive shafts. The bushes have a conical outer surface and a cylindrical inner bore with H7 tolerance including a standardized keyway. Once fixed, the component is capable of transmitting torque while

Dimensions & Rating Table 1008 - 3030 3535 - 6050 7060 P-1954-TBW 5/18 www.tbwoods.com 65 Inch Bores TAPER-LOCK BUSHINGS Part Number Bore Keyseat Weight TL1008 BUSHINGS TL100812 1/2 1/8 x 1/16 0.3 TL10089/16 9/16 1/8 x 1/16 0.3

Object Moved This document may be found here

Tsubaki of Canada Limited, 1630 Drew Road, Mississauga, ON L5S 1J6 Tel: 905-676-0400 Fax: 905-676-0904 Toll-Free: 800-263-7088 www.tsubaki.ca e-mail: [email protected] SprocketsE137 S e c t i o n E “Taper-Lock”StyleBushings 3535-5050 Std. Std. Bushing F

L - Space required to tighten bushing or loosen to remove hub with puller using short hex key. M - Space required to remove bushing using screws as jackscrews - short hex key - no puller reuired. Listed required hub diameter is for reference only. Severe conditions may require larger hub and in some cases a slightly smaller hub may be satisfactory.

3535 B 127,0 88,9 4030 B 146,0 76,2 4040 B 146,0 101,6 4535 B 162,0 88,9 4545 B 162,0 114,3 5040 B 177,5 101,6 5050 B 177,5 127,0 Taper Bush Dimensions Bore (F8) b h mm 1008 1108